HVAC, IAQ, & PLumbing Services in Hartford, WI

Performed comprehensive tune-up on customer's furnace system, including inspection of internal components, electrical connections, and ductwork. Cleaned blower assembly and verified proper operation of control board and safety switches. Checked and cleaned PVC venting system to ensure proper exhaust flow. All systems tested and confirmed to be operating within manufacturer specifications.

Performed comprehensive inspection of HVAC system in utility area, examining PVC condensate drainage lines and galvanized sheet metal ductwork connections. Verified proper ventilation flow and checked mechanical components for functionality, ensuring all systems are operating within specifications for the upcoming season.

Responded to no heat complaint on newer residential HVAC system. Inspection of utility area revealed issue with expansion tank and circulation system. Serviced the yellow valve assembly on primary piping network and verified proper operation of the WATTS expansion tank. System was restored to normal heating function after adjustments to the boiler connections and circulation components.

Installed new Capri water softener/filtration system in utility area, connecting to existing copper plumbing with appropriate shut-off valves. Set up complete drain line configuration using PVC piping and connected system to electrical supply. Tested system operation to ensure proper functionality.

Completed routine tune-up of HVAC system and identified moisture issues in the utility area. Inspected PVC drainage pipes which were found to be properly installed with no visible damage or leaks; however, noted standing water on concrete floor near electrical cables which requires further investigation to prevent potential hazards and system damage.

Performed comprehensive tune-up on residential HVAC system, including inspection of furnace interior components, electrical connections, and blower motor assembly. Verified proper leveling of equipment using spirit level to ensure optimal operation and airflow balance. All systems tested and confirmed to be functioning within manufacturer specifications.

Completed installation of a complete HVAC system in residential basement, including a new high-efficiency furnace with PVC ventilation pipes and integrated air filtration component. System was properly mounted, connected to existing ductwork, and all electrical connections were secured according to manufacturer specifications, with final inspection of control board and motor functionality confirming proper operation.

Responded to no-heat call for aging residential furnace (10+ years old). Upon inspection, removed front panel to access internal components and found faulty igniter preventing system startup. Replaced igniter assembly, cleaned flame sensor, and inspected heat exchanger through viewing port. System now operating correctly with proper ignition sequence and heat output.

Completed furnace installation with successful system commissioning. Performed pressure testing using digital manometer, confirming proper gas pressure readings of 9.08" WC, which falls within manufacturer specifications. All connections were verified and system operation validated prior to completion.

Performed comprehensive tune-up on residential furnace system, including thorough inspection of internal electronic components, circuit boards, and mechanical parts. Utilized diagnostic equipment to test electrical systems and verify proper functioning of all components. Ensured proper ventilation through PVC exhaust pipes and confirmed all connections were secure for optimal system performance.

Performed routine HVAC tune-up service including comprehensive pressure testing using dual port manometer. Readings of 35.7/34.7 inWC and 351/347 pascals were documented, confirming system is operating within manufacturer specifications. All pressure differentials were verified to be within acceptable parameters for optimal system performance.

Performed comprehensive tune-up service on the air handler unit, inspecting the evaporator coil and copper refrigerant lines which were found to be in good condition with no signs of corrosion or leakage. Temperature measurements indicated proper system operation with supply air temperature at 116.5°F, confirming the heating cycle is functioning within normal parameters. All connections were verified secure and the system is operating efficiently.

Completed tune-up service on HVAC system, verifying proper leveling of mounting bracket installation using built-in spirit level. Inspected plumbing connections including PVC, copper, and galvanized steel pipes, confirming all components were properly installed and functioning as designed.

Diagnosed and repaired a no-heat condition on a residential boiler system less than 10 years old. Inspection revealed a faulty circulator pump and clogged condensate line causing system shutdown. Replaced circulator pump, cleaned condensate drain, and verified proper system operation with normal heating function restored.

Performed diagnostic service on Armstrong furnace showing no heat operation. Removed access panel to inspect internal components including control board, gas valve assembly, and blower motor. Identified significant corrosion on electrical connections and wear on multiple components consistent with 10+ year old system. Cleaned electrical contacts, tested ignition sequence, and restored heating function. Recommended customer consider replacement options within next 1-2 heating seasons due to age-related component deterioration observed throughout system.

Inspected Bryant furnace unit with front panel removed for comprehensive system evaluation. Observed exposed control board, internal wiring, and connected ductwork. Noted electrical wiring issue requiring attention where single black wire protrudes through floor with visible rust/corrosion around penetration point.

Responded to no-heat call on newer furnace unit. Diagnosed issue with ignition sequence - observed flame rollout during startup. Removed access panel to inspect components, found inducer motor failing to maintain proper draft. Replaced draft inducer assembly and verified proper ignition sequence with sustained blue flame. System now operating within normal parameters with appropriate airflow and combustion.

Diagnosed electrical issues on aging furnace with clamp meter showing 122.3V. Accessed internal components by removing panels to inspect control board, blower motor assembly, and wiring connections. Identified and repaired faulty wiring in the control circuitry to restore proper heating function.

Completed replacement of existing HVAC system with new equipment including outdoor condenser unit installed on concrete pad and indoor furnace with proper ductwork connections. Installation included all necessary refrigerant lines, electrical connections, PVC venting, and condensate drainage to ensure full system functionality and compliance with manufacturer specifications.

Conducted comprehensive inspection of electrical panel and window installation in preparation for HVAC system replacement. Documented existing electrical infrastructure to ensure proper load capacity for new equipment. Evaluated window placement and structural elements in partially renovated space to determine optimal positioning of replacement HVAC components.