Heating, Cooling, and Plumbing Repair Services in Menomonee Falls, Wisconsin

Performed an indoor air quality (IAQ) estimate, inspecting the Daikin gas furnace, galvanized supply plenum and ductwork, PVC venting, and the atmospherically vented water heater in the basement mechanical area. Equipment and ductwork appeared clean and in good condition with no visible rust, frost, or damage, and an existing cabinet-style device (air cleaner/humidifier) was noted on the supply duct. Documented the system with photos to evaluate IAQ improvement options.

Performed an on-site estimate for replacement of a gas power-vent water heater, assessing the existing tank, PVC exhaust venting, gas supply piping, and surrounding supply plumbing for code-compliant removal and installation. Also evaluated the sump pump system for replacement with a battery backup unit, documenting existing conditions and noting that clutter and stored materials in the work areas will need to be cleared for safe access.

Responded to a no-heat complaint (warm air at vents with furnace not firing) and performed a full furnace tune-up, inspecting the air handler, plenum transition, condensate drain piping, and refrigerant line connections, with no visible rust, frost, or cracking noted. Also completed a humidifier tune-up to restore proper operation and ensure the system is running safely and efficiently.

Installed a new Bradford White gas-fired tank water heater with copper supply piping, brass fittings, and isolation valves, and added a thermal expansion tank to protect the system from pressure fluctuations. Connected the galvanized flue vent to the chimney with proper elbow routing, then verified connections and confirmed the unit was free of leaks and operating correctly.

Performed a seasonal heating maintenance inspection on the gas furnace, removing the access panel to visually inspect the burner assembly, gas valve, inducer blower motor, flame sensor wiring, and condensate/venting PVC piping. All components were found intact with light dust accumulation and no signs of rust, frost, or physical damage, indicating the unit is in good operating condition and ready for the heating season.

Diagnosed a no-hot-water complaint on a gas-fired tank water heater where the pilot would light briefly but fail to stay lit, inspecting the unit, gas supply piping, flexible connectors, and galvanized vent connection with no visible leaks, corrosion, or venting obstructions. Performed repair to restore reliable pilot and burner operation, then relit the appliance and verified sustained flame and proper draft. System is operating normally and producing hot water.

Completed comprehensive furnace and air conditioning tune-up service on residential HVAC system located in mechanical space. Performed standard preventive maintenance inspections on heating and cooling equipment, including examination of condensate pump assembly, drainage systems, and associated PVC piping configurations. All system components inspected and found operating within normal parameters.

Completed comprehensive furnace and air conditioning tune-up service including inspection of outdoor condensing unit and associated plumbing components. Unit exterior showed normal seasonal debris accumulation; all mechanical systems inspected and verified operational, with water heater ventilation and PVC drainage systems confirmed properly installed per manufacturer specifications.

Completed comprehensive furnace tune-up including full system inspection, testing of all safety controls, and verification of proper operation on Lennox heating unit. Inspected control board connections, burner assembly, heat exchanger, and blower components; all systems found operating within manufacturer specifications with no issues identified.

Responded to no cooling callback on residential HVAC system. Upon arrival, connected manifold gauges to outdoor condensing unit and performed system diagnostics. Pressure readings indicated abnormally high head pressure on the high side (687 psig) and elevated suction pressure on the low side (585 psig), with superheat reading of 71°F suggesting potential airflow restriction or system overcharge. Removed top access panel to inspect condenser fan operation and internal components. Based on gauge readings and visual inspection, identified issue preventing proper cooling operation and addressed accordingly to restore system functionality.

Responded to customer complaint of delayed start on air conditioning unit occurring over several nights. Performed diagnostic evaluation using digital manifold gauges to assess system pressures and temperatures on Lennox Elite unit. Verified thermostat operation and settings, confirming unit communication and proper display function at 65°F current temperature with 70°F setpoint.

Completed on-site evaluation of existing natural gas furnace and air conditioning system located in basement. Both units are operational but aging and nearing end of serviceable life. Documented current equipment configuration including outdoor condensing unit on concrete pad with proper electrical disconnect, and basement-mounted furnace with existing ductwork infrastructure. Provided comprehensive replacement estimate for new high-efficiency furnace and AC system to homeowner.

Completed full boiler replacement in basement mechanical room with all required permits and licensed electrician coordination. Installed new boiler unit with complete copper piping distribution system, expansion tank, water filtration system, gas valving with safety shutoffs, and proper venting through foundation wall with sealed penetration. All connections, fittings, ball valves, and control wiring installed to manufacturer specifications and local code requirements, with system tested and operational upon completion.

Completed comprehensive tune-up service on both furnace and air conditioning system. Performed standard maintenance procedures including inspection of condensate drain assembly with copper refrigerant lines, verified proper operation of outdoor condenser unit, and conducted system diagnostics with manifold gauges to ensure optimal performance of both heating and cooling equipment.

Completed comprehensive tune-up on residential HVAC system including furnace and air conditioning condensing unit. Performed standard maintenance inspection of indoor air handler with verification of refrigerant lines, condensate drainage system, gas connections, and electrical components. Conducted outdoor condensing unit evaluation with electrical testing using multimeter to verify proper voltage and amperage readings, ensuring system operating within manufacturer specifications.

Responded to no heat call with reported odor and non-functioning air conditioning system. Upon arrival, inspected residential furnace unit in utility closet and found system operational with ambient temperature reading of 72.9°F. Performed visual inspection of furnace cabinet, refrigerant lines, condensate drain, and ductwork connections. No active fault conditions detected at time of service call. Unit appeared to have accumulated normal dust and debris on exterior surfaces. All visible components including copper refrigerant lines with insulation, PVC condensate piping, and electrical connections showed no signs of immediate failure or safety concerns.

Completed comprehensive tune-up and inspection on residential HVAC system, unit model A95UH100700B123-03. Performed standard maintenance procedures including inspection of evaporator coil assembly, refrigerant lines, and internal components. All mechanical and electrical systems verified operational, with unit showing normal wear patterns consistent with age and usage.

Completed estimate for replacement of aging HVAC system including natural gas furnace and air conditioning unit. The existing furnace, manufactured in 1997 and located in the basement, remains operational but has reached end of service life. The outdoor condenser unit shows visible deterioration with significant rust on fan components and motor mounting areas. Provided comprehensive replacement options for both heating and cooling equipment to address the aging system and improve efficiency and reliability.

# Preventive Maintenance Service Completed Performed comprehensive cooling system tune-up on residential Lennox air conditioning unit as part of recurring membership maintenance agreement. Conducted complete system diagnostics using Fieldpiece SMAN refrigerant manifold to verify proper refrigerant pressures, temperatures, and overall system performance. All measured parameters including suction and discharge temperatures, superheat, and subcooling readings were within manufacturer specifications. Inspected condensing unit exterior condition, verified proper airflow through condenser coil louvers, and confirmed secure mounting on equipment pad. Checked electrical connections, refrigerant line insulation, and PVC condensate drain routing for proper installation and function. Unit operating efficiently with no deficiencies noted during inspection.

Evaluated existing Richmond 40-gallon power vent water heater nearing end of service life in basement utility area. Documented current installation including copper supply lines, gas connections, venting system, and surrounding plumbing infrastructure to provide accurate replacement estimate.