Heating, Cooling, and Plumbing Repair Services in Menomonee Falls, Wisconsin

Responded to no cooling call on residential air conditioning system. Upon arrival, located outdoor condenser unit on concrete pad against exterior wall. Connected manifold gauge set to system to diagnose issue. Performed pressure testing and system evaluation to determine cause of cooling failure. Communicated findings and obtained approval to proceed with necessary repairs. System serviced and restored to proper operation.

Responded to callback for AC unit that stopped running following tune-up service performed earlier in the week. Upon arrival, diagnosed failed dual run capacitor as cause of system failure. Replaced defective 3.0 MFD capacitor with new unit, verified all electrical connections, and tested system operation. Unit restored to normal cooling operation with proper amp draw and no further issues detected.

Responded to no cooling complaint on Lennox system. Upon arrival, performed diagnostic testing of refrigerant charge using manifold gauges on R410A system. Measured operating pressures and temperatures, finding subcooling at 30°F and superheat at 61°F, indicating improper refrigerant charge. Inspected control board for proper operation and verified all electrical connections and relays functioning correctly. System restored to proper cooling operation after addressing refrigerant charge issue.

Responded to no cooling call with furnace blower running louder than normal and first floor temperature dropping from 73°F setpoint to 70°F. Upon arrival, customer had shut down all equipment due to concern about potential damage. Performed system inspection of furnace and air handler unit, evaluated blower motor operation and noise levels, checked airflow and ductwork connections, and verified proper system function after identifying and resolving the issue preventing adequate cooling.

Completed preventive maintenance tune-ups on two furnace units and two air conditioning units in residential basement installation. Performed comprehensive system inspections including visual examination of all components, verification of proper operation, and documentation of equipment conditions. All units were found to be in operational condition with manufacturer labels and specifications clearly visible on equipment panels.

Responded to emergency service call for furnace and air conditioning system evaluation and replacement estimate. Conducted comprehensive assessment of existing HVAC equipment, documented electrical panel configuration showing dedicated AC circuit breaker, and photographed condensate pump installation with PVC drainage system in mechanical area. Provided detailed replacement options and specifications for new heating and cooling equipment suitable for the property.

Responded to no-cooling call on aging HVAC system. Upon arrival, confirmed outdoor fan motor operation but unit failed to produce cooling. Diagnosed failed compressor on 10+ year old air conditioning system and recommended full system replacement due to age and repair costs exceeding value of equipment. Customer approved replacement, and new system was installed and tested successfully.

Responded to customer concern regarding inadequate cooling distribution in 3-zone system with open floor plan, where cold air was settling in basement while upper bedrooms remained warm. Inspected air handler unit and ductwork in attic space and evaluated zone control system and damper operations. Assessed return air flow patterns and identified insufficient return air pathways from basement level causing air stratification issues. Documented current HVAC equipment configuration including air handler, zone dampers, and existing ductwork layout with photos. Provided recommendations for improving air circulation including potential installation of additional return air grilles in basement, balancing dampers, or supplemental circulation fans to promote better air movement between levels and achieve more uniform temperature distribution throughout the home.

Completed semi-annual preventive maintenance inspection as part of prepaid membership service. Performed system diagnostics including supply air temperature measurements at ductwork, recording 67.0°F and 54.6°F readings to verify proper airflow and temperature differential across the HVAC system.

Completed comprehensive AC and furnace tune-up service, performing system diagnostics with digital manifold gauges to verify refrigerant pressures, temperatures, and overall system performance. Inspected mechanical components including copper refrigerant lines, insulated ductwork, and plumbing connections to ensure proper operation and identify any maintenance needs. Customer expressed interest in enrolling in ongoing maintenance membership program for continued system care.

Completed air conditioning tune-up on outdoor condensing unit. Removed and inspected heavily soiled air filter showing significant dirt accumulation, indicating proper filtration but need for replacement. Performed standard maintenance procedures including system inspection, component cleaning, and verification of proper operation.

Responded to service call for newly installed ductwork system producing abnormal noise. Upon inspection, identified improper joint connection in attic ductwork with visible separation and inadequate sealing at metal duct junction. Repaired and resealed ductwork joints with proper mastic application to eliminate air leaks and vibration noise, ensuring system operates quietly and efficiently within manufacturer specifications.

Provided comprehensive estimate for complete HVAC system replacement including air conditioning unit and furnace. Customer approved proposal following concerns about repeated coil failures and requested aluminum coil material for improved longevity. Assessment confirmed inadequate airflow distribution to second floor affecting both heating and cooling performance. Estimate addresses equipment replacement to resolve ongoing maintenance issues and improve system efficiency throughout multi-level residence.

Completed comprehensive furnace tune-up including full system diagnostics and performance verification. Utilized SC680 multimeter to test electrical components, measure voltage levels, and verify capacitor functionality on the outdoor condensing unit. Inspected and assessed all internal electrical connections, circuit board operation, and compressor components with access panel removed for thorough evaluation. All systems tested within normal operating parameters and unit returned to service.

Completed comprehensive preventive maintenance tune-up on residential air conditioning system. Performed standard inspection procedures including refrigerant level check, electrical component testing, and condenser unit evaluation to ensure optimal system performance and efficiency for the cooling season.

Responded to service call for continuously running HVAC system with 40+ year old equipment. Upon inspection, found evaporator coil severely frozen with heavy ice accumulation, measuring 64°F surface temperature. Diagnosed issue as likely caused by restricted airflow, low refrigerant charge, or failed control board preventing proper system cycling. Inspected outdoor unit control panel revealing disorganized wiring, aging capacitor, contactor, and transformer. Due to advanced age of equipment and extent of freeze-up, recommended system evaluation after thaw and potential replacement given the unit's age exceeding typical service life expectancy.

Completed scheduled membership cooling system maintenance visit during morning arrival window. Performed comprehensive inspection of residential HVAC system, including internal furnace components with access panel removed to examine blower motor, wiring harnesses, and control boards. Utilized manifold gauge set to test and verify refrigerant pressures and system charge levels. Inspected refrigerant lines, PVC venting, and overall system operation to ensure proper functionality for the cooling season.

Diagnosed and repaired leaking outdoor hose bib by installing a new brass quarter-turn ball valve with yellow handle lever on the blue supply line in the crawl space. The new valve assembly was properly secured and tested to ensure no leaks at the exterior spigot location where the fixture emerges through the concrete foundation near the house siding.

Completed comprehensive tune-up service on Lennox furnace and air conditioning system. Performed standard maintenance inspection of all system components, verified proper operation of heating and cooling functions, checked refrigerant lines and connections, inspected PVC intake and exhaust venting for proper installation and clearance, and confirmed electrical connections at disconnect panel. All equipment found to be operating within normal parameters with no immediate service needs identified.

Completed comprehensive tune-up service on Bryant furnace and outdoor AC condenser unit. Performed standard maintenance inspection of all heating and cooling components, verified proper operation of both systems, checked refrigerant lines, inspected ductwork connections, and confirmed condensate drainage functioning correctly.