Heating, Cooling, and Plumbing Services in New Berlin, WI

Completed install callback and performed combustion analysis on recently installed heating system. Bacharach combustion analyzer readings confirmed proper operation with oxygen levels at 4.5%, carbon monoxide at 32 ppm, efficiency at 83.0%, and carbon dioxide at 12.2%, all within acceptable parameters for safe and efficient system performance.

Completed comprehensive HVAC tune-up service on residential air handler system located in basement utility area. Performed standard maintenance procedures including inspection of refrigerant lines, ductwork connections, condensate drainage system, and electrical components. All mechanical systems were found operating within normal parameters, with PVC drainage lines and copper refrigerant tubing showing proper installation and no visible defects.

# Warranty Service Completed Responded to warranty service call for HVAC furnace unit. Upon arrival, removed access panel to perform comprehensive system inspection. Examined all internal components including blower motor assembly, inducer motor, gas valve connections, and electrical wiring harnesses. Inspected black condensate drainage pipes for proper flow and verified no blockages present. Checked all wire connections including green ground wires and multi-colored control wiring for secure terminations. Verified proper operation of white control board with associated switching mechanisms and confirmed all safety circuits functioning correctly. Inspected metallic cylindrical motor assemblies and associated mounting hardware for secure installation. All components found operating within manufacturer specifications. Unit tested and returned to normal operation.

Completed routine HVAC maintenance inspection on prepaid service agreement. Performed temperature diagnostics in attic space using infrared thermometer to verify proper system operation and insulation effectiveness. Inspected basement mechanical area including main supply ductwork, flexible branch lines, and HVAC infrastructure to ensure proper airflow and system integrity. All equipment operating within normal parameters with no deficiencies noted.

Completed plumbing estimate for powder room fixture replacement. Assessed existing undermount sink with bronze two-handle faucet and evaluated under-cabinet plumbing configuration, including PVC P-trap assembly, chrome tailpiece with mounting flange, and flexible braided water supply lines. Provided detailed estimate for potential fixture upgrades and plumbing component replacements as requested.

Completed HVAC system replacement estimate for residential property. Assessed existing Royalton furnace unit located in utility room, evaluating current ductwork configuration including flexible metal ducts, PVC intake/exhaust venting system, and associated copper piping connections. Documented equipment condition, spatial constraints, and installation requirements to provide comprehensive replacement recommendations for upgraded heating and cooling system.

Performed sump pump inspection and documentation in residential basement utility space. Examined existing sump pump system including discharge piping with PVC connections, pump basin condition, and operational components. Basin showed significant sediment buildup, mineral deposits, and water level staining on interior walls, indicating regular water accumulation and pump cycling. Documented pump housing condition, discharge pipe configuration with visible red coupling connection, and drainage system including corrugated intake line. System components appeared functional with proper floor drain cover installation and secure pipe mounting hardware in place.

Responded to a plumbing service call for shower/tub issues and performed an inspection of the water supply system. Upon investigation, discovered severely corroded galvanized piping with extensive mineral buildup and scale accumulation that had significantly restricted water flow and reduced the internal diameter of the pipes. Replaced the deteriorated pipe section with new copper piping, installing compression fittings to ensure proper connections. The old pipe exhibited heavy corrosion throughout, with thick crusty deposits coating the interior walls, which was causing reduced water pressure and flow issues to the shower/tub fixtures. Completed the pipe replacement in the basement/crawl space area, securing all new copper lines properly along the existing floor joists to restore full water flow capacity to the bathroom fixtures.

Completed commercial HVAC equipment replacement estimate for a food processing facility, assessing existing rooftop unit mounted in mechanical room with wall-mounted controls and evaluating requirements for new equipment installation to maintain proper temperature control and air quality standards in the production area. Documented current system configuration including mounting hardware, electrical connections, ductwork connections, and thermostat placement to ensure accurate replacement specifications for the climate-controlled food preparation environment with multiple work stations.

Completed installation and startup of tankless water heater system with all internal components properly mounted and configured within white metal enclosure. Verified proper connections of copper supply lines, gas valves with yellow handles, heat exchanger assembly, control board wiring, and circuit panel functionality, with all piping extending through floor penetrations and system tested for safe operation.

Completed sump pump installation in basement utility area, including new discharge piping system with white PVC drainage lines and proper floor drain connection. Installed copper piping assembly with ball valves (blue and red handles for easy identification) connected to the pump system, along with pressure relief components and necessary fittings to ensure proper operation and code compliance.

Completed comprehensive tune-up maintenance on residential gas furnace system. Performed full system inspection including gas valve operation, control board functionality, electrical connections, and venting components. Verified proper operation of all safety controls, confirmed adequate combustion air supply through PVC intake piping, and ensured exhaust venting meets code requirements.

Conducted comprehensive evaluation of existing residential HVAC system located in basement utility area for equipment replacement estimate. Assessed current furnace unit, ductwork configuration, and associated mechanical components including water heater connections and ventilation systems. Documented equipment condition, spatial constraints, existing infrastructure including exposed ceiling joists, concrete flooring, and proximity to adjacent storage areas. Photographed current installation showing beige furnace with metallic ductwork, insulated ventilation components, electrical connections, and copper and PVC piping arrangements to provide detailed reference for replacement specifications and system upgrade recommendations.

Completed prepaid HVAC maintenance visit and performed system inspection. Examined flame sensor electrode, which showed signs of carbon buildup, and inspected pipe insulation for proper sealing and condition. All components were evaluated for proper operation and system readiness.

# Plumbing Install - Piping Job Description Completed installation of white PVC piping system spanning ceiling cavity and interior wall framing. Routed Type CAE/LINE PVC pipe through overhead space above drop ceiling, utilizing proper fittings including T-joints and elbows to achieve required configuration. Secured piping to wooden joists with appropriate hangers and supports to prevent sagging and ensure code compliance. Installed vertical PVC pipe runs through exposed wall framing, connecting to white plastic junction box housing red and blue valve controls. Configured complex routing pattern with multiple elbows and joints to navigate structural obstacles and achieve proper drainage slope. Integrated piping system through floor penetrations, ensuring proper sealing and support at transition points. Mounted control valve assembly to wall studs at accessible height for future maintenance and operation. Verified all connections were properly solvent-welded and pressure-tested system

# HVAC Install - Ductwork Service Report Completed installation of new ductwork system in residential attic space, including rigid metal supply ducts with flexible elbow connections to ensure proper airflow routing around structural beams. Installed new wall-mounted air return vent register in living space with proper integration to existing HVAC system, securing all connections and verifying adequate air circulation throughout the conditioned area.

# HVAC Service Report - Furnace Maintenance Performed comprehensive inspection and maintenance service on residential forced-air heating system located in basement mechanical room. System consists of central air handler unit with integrated ductwork distribution system and Honeywell HE225A flow-through humidifier mounted on supply plenum. Conducted thorough visual inspection of air handler cabinet, noting accumulated dust and debris on exterior surfaces and surrounding ductwork components. Inspected all accessible ductwork connections including horizontal supply trunk lines and flexible duct transitions for proper sealing and structural integrity. Verified secure mounting of all equipment and absence of excessive vibration points. Examined whole-home humidification system including Honeywell HE225A unit mounted to supply duct. Inspected copper water supply line with shutoff valve for proper connection and absence of leaks. Verified humidistat wiring connections and control circuit f

# Plumbing Estimate - Sump Pump Conducted comprehensive assessment of existing sump pump system in basement crawl space. Inspected sump basin installation, pump mechanism, and associated discharge piping configuration. Evaluated PVC discharge line connections, check valve installation, and electrical cord routing for code compliance and operational efficiency. Documented current pump positioning within basin and verified proper float switch clearance. Assessed surrounding concrete floor conditions and structural framing around pit opening. Noted deteriorated fiberglass insulation in overhead joist bays indicating potential moisture infiltration concerns that may impact pump workload. Photographed complete system layout including piping connections, basin condition, and utility area infrastructure to provide detailed documentation for estimate preparation.

# Plumbing Service - Inspection Summary Conducted comprehensive plumbing inspection of residential basement mechanical room and water treatment system. Inspected Coleman water softener installation including copper supply lines, multiple ball valve shutoff points, and proper electrical connections. Verified water softener control panel operation and examined plumbing configuration for compliance with installation standards. Evaluated furnace area plumbing connections including gas line routing, PVC exhaust/intake venting system, and associated mechanical equipment installations. Inspected all visible piping for proper support, secure fittings, and absence of leaks or corrosion. Confirmed adequate clearances around equipment and proper installation against foundation walls. Documented current condition of all plumbing components with photographic evidence for service records. All inspected systems found to be functioning within normal parameters with professional-grade installations

Performed comprehensive inspection of ductwork system, identifying significant dust accumulation and early-stage corrosion at connection points. Interior examination revealed perforated sections with visible rust formation and debris buildup that could potentially restrict airflow and reduce system efficiency.