HVAC & Plumbing Services in Oak Creek, WI Since 1929

Completed installation of new air conditioning condenser unit and evaporator coil at residential property. Positioned outdoor condenser on concrete pad against exterior wall with proper clearances, installed condensate drain safety switch with wiring routed through metal plenum, and verified all electrical connections and refrigerant lines are secure and operational.

# HVAC Furnace Installation Completed residential furnace installation in basement utility area. Installed new heating system with integrated ductwork assembly featuring galvanized sheet metal pentagonal trunk line for optimal airflow distribution. Connected copper refrigerant lines and configured system alongside existing Rheem water heater. Performed comprehensive system pressure testing using digital manifold gauge, verifying proper refrigerant pressures at 130 PSI on both high and low side ports to ensure system operates within manufacturer specifications. All mechanical connections secured, ductwork properly sealed, and system commissioned for reliable operation.

Completed full HVAC system replacement including installation of new high-efficiency furnace in basement mechanical room and matching outdoor condensing unit. Furnace was positioned on existing concrete pad with proper clearances, connected to white PVC venting system for intake and exhaust, and integrated with existing ductwork distribution system. Outdoor condensing unit was set on level concrete pad with appropriate drainage, electrical disconnect box mounted to exterior wall with PVC conduit for line set protection, and all refrigerant lines properly insulated and secured. System was pressure tested, evacuated, charged to manufacturer specifications, and cycled through multiple heating and cooling operations to verify proper function of all components including blower motor, compressor, and safety controls.

Completed comprehensive plumbing inspection of residential kitchen and basement utility systems. Examined under-sink garbage disposal installation, verifying proper mounting, electrical connections, and PVC drain configuration, as well as basement water supply system including main distribution lines, shut-off valves, and mechanical equipment connections. All components found to be properly installed and functioning within normal parameters.

Completed comprehensive HVAC system replacement estimate for residential property. Assessed existing outdoor condenser unit currently protected with seasonal cover and evaluated electrical service capacity by inspecting main distribution panels in basement utility area. Documented equipment location, electrical infrastructure, and site conditions to develop specifications for new system installation including proper electrical requirements and outdoor unit placement considerations.

# HVAC Service Report Responded to service call for Wood Heat by Lennox air handler system. Performed diagnostic inspection of unit with cabinet access panel removed to assess internal components across all three compartment levels. Inspected heat exchanger assembly, blower housing, electrical control board, transformer, and associated wiring systems throughout upper, middle, and lower sections. Verified proper connections of multi-colored electrical wiring including power and control circuits. Evaluated condition of motor assembly and control components in lower compartment. Unit showed normal operational wear with dust accumulation on internal surfaces. Documented system configuration and current operating condition through photographic records for service history.

Completed routine furnace maintenance and filter inspection. Removed and examined the existing 14x25x1 air filter, which showed minimal contamination and remained in serviceable condition. Filter housing and frame components were found to be secure and properly seated within the HVAC system, ensuring optimal airflow and system efficiency.

Completed scheduled HVAC maintenance on an International Comfort Products gas furnace, model GGMVE080T71GA (80,000 BTU input capacity, manufactured October 2013). Documented unit specifications and verified AHRI certification status as part of the prepaid maintenance visit.

Completed installation of Carrier furnace unit (Model: SBLRMAM02MUN1Y11G, Serial: 5M2535L955) in basement utility area. Unit was positioned and secured with proper clearances maintained from stored items and existing HVAC ductwork, all electrical connections completed, and system tested for proper operation.

# HVAC Install - Complete System ## Summary Completed full HVAC system installation including outdoor Carrier condenser unit with electrical service components and indoor mechanical equipment with associated connections and controls. ## Work Performed **Outdoor Equipment Installation:** Installed Carrier brand air conditioning condenser unit on prepared black concrete pad against exterior brick wall. Positioned unit to ensure proper clearance and accessibility for future maintenance. Mounted electrical disconnect box and meter socket on brick wall with white electrical conduit running vertically to service the outdoor unit. Secured all electrical connections per manufacturer specifications and local electrical codes. Verified proper grounding and bonding of all electrical components. **Indoor Equipment Installation:** Installed cylindrical mechanical equipment in basement utility area with proper clearance from walls and surrounding structures. Connected multiple refrigerant lines

Performed comprehensive tune-up and inspection on Carrier HVAC system, including examination of all internal components, electrical connections, control boards, and blower assembly. Verified proper operation of all mechanical systems, checked condensate drainage lines, and confirmed secure mounting of all wiring harnesses and safety controls.

Completed comprehensive HVAC system evaluation for residential forced-air furnace and air handler replacement in basement utility area. Assessed existing beige furnace unit with curved gray supply ductwork, examined electrical panel capacity and circuit breaker configuration to ensure adequate power supply for new equipment installation, and documented current system layout including insulated duct runs and mechanical connections for replacement specifications.

Completed comprehensive tune-up service on residential furnace system in basement mechanical room. Performed standard maintenance protocol including inspection of heat exchanger, burner assembly, and blower components; verified proper operation of all safety controls and limit switches; checked and documented ductwork connections and condensate drainage system. All equipment operating within manufacturer specifications with no deficiencies noted at time of service.

Responded to commercial toilet maintenance call and performed internal tank inspection and component assessment. Removed tank lid to evaluate flushing mechanism, which revealed significant mineral buildup and discoloration throughout tank interior indicating extended service life. Inspected float ball assembly with plastic arm mechanism and blue base component for proper operation. Assessed tank condition showing brown water staining and mineral deposits concentrated around waterline and mechanical connection points. Documented existing flush valve system and chrome flush handle operation. Tank components showed age-related wear but remained functional. Verified toilet positioning and surrounding fixtures in commercial restroom environment with proper mounting and stability.

Completed comprehensive HVAC system replacement estimate for residential property. Assessed existing furnace unit located in basement mechanical room and evaluated current ductwork configuration, including main trunk lines and vertical distribution sections. Documented exterior utility connections and meter locations to determine optimal equipment placement and necessary modifications for new system installation.

Completed installation of residential water heater system in basement utility area. Installation included proper connection of copper supply lines, mounting and integration of blue expansion tank with brass fittings, and installation of insulated piping for hot water distribution. All connections were secured according to manufacturer specifications, with PVC drainage/ventilation system positioned appropriately and shutoff valve installed for system control.

Completed water heater replacement in basement utility area. Removed existing unit and installed new cylindrical water heater tank with proper venting system, including galvanized metal ductwork with elbow joint extending through ceiling joists. Connected copper supply lines, gas piping with shut-off valve, and integrated all plumbing connections to existing infrastructure, securing pipes to wooden joists with appropriate strapping and supports.

Completed comprehensive estimate for complete HVAC system replacement at residential property. Evaluated existing outdoor condensing unit positioned against exterior brick wall with current electrical disconnect and conduit routing, as well as interior electrical panel and distribution system in basement utility area. Assessment included documentation of existing equipment placement, electrical service configuration with dual-column circuit breaker panel, and current ductwork installation to provide detailed replacement specifications and equipment sizing recommendations for new high-efficiency heating and cooling system installation.

Completed warranty inspection of newly installed HVAC system in basement mechanical room. Verified proper installation of main trunk ductwork, supply plenum, and air handler unit with all components secured according to manufacturer specifications and local building codes. Documented installation quality through photographic records showing ductwork transitions, support systems, and equipment placement meeting warranty requirements.