Heating, Cooling and Plumbing Services in Waterford, Wisconsin

Conducted estimate for replacement of existing water heater installed in 2002. Evaluated current installation including ductwork, plumbing configuration with PEX piping, and available space in mechanical room. Discussed tankless water heater options with customer as alternative to conventional tank-style unit, reviewed installation requirements, venting considerations, and system specifications suitable for the property.

Completed installation of new furnace and humidifier system in residential basement location. Installed gray metal vertical cabinet-style furnace unit with associated ductwork connections, routing large supply and return ducts through exposed ceiling joists. Connected humidifier equipment to system, with PVC condensate drainage piping staged for final connection. All equipment properly positioned on concrete floor, ductwork secured to ceiling structure with appropriate hangers, and system prepared for startup and commissioning.

Completed routine cooling system maintenance visit as part of recurring membership agreement. Performed standard diagnostic checks using manifold gauge set to verify refrigerant pressures and system performance on horizontal air handler unit located in attic space. Inspected equipment operation, condensate drain lines, and ductwork connections to ensure proper system functionality.

Conducted estimate for complete HVAC system replacement in basement installation. Existing furnace (80,000 BTU natural gas unit) is non-operational and requires replacement along with air conditioning system. Assessed current equipment configuration, measured installation area, and documented existing ductwork layout including supply and return air pathways. Provided estimate for new furnace and AC system with promotional offer including complimentary water heater replacement. Documented equipment specifications, clearance requirements, and necessary modifications for proper installation.

Completed comprehensive AC tune-up on Carrier system, including indoor furnace and outdoor condenser unit inspection. Performed standard maintenance procedures with refrigerant pressure testing using manifold gauges, electrical component verification, and system operational checks. All equipment found operating within normal parameters with no issues identified during service visit.

Responded to no heat call on a two-zone hydronic boiler system. Upon arrival, found the zones were not operating independently as designed. Performed diagnostic evaluation of the boiler, circulator pumps, zone valves, and associated controls. Inspected gas valve, burner assembly, and all electrical connections within the heating unit. Verified proper operation of expansion tank, air separator, and piping configuration. Tested system controls and thermostats to ensure proper zone isolation and independent operation. Restored heat to the residence and confirmed both zones were functioning correctly before departure.

Conducted on-site assessment for sump pump and battery backup system installation in crawl space area. Evaluated existing sump pump that has been inactive for approximately two decades and documented current mechanical equipment configuration including discharge piping and electrical components for comprehensive estimate preparation.

Completed prepaid membership cooling maintenance visit on residential air conditioning system. Performed standard seasonal inspection of outdoor condenser unit, including visual assessment of cabinet condition and component integrity. Connected manifold gauge set to measure refrigerant pressures and verify system charge levels. Inspected electrical components including run capacitor and associated wiring connections, confirming proper terminal connections and component functionality. All system parameters found operating within normal specifications.

Completed furnace and air conditioning tune-up for new homeowner requesting equipment evaluation. Performed comprehensive inspection of HVAC system including furnace/air handler unit and associated condensate drainage system with PVC piping configuration. All equipment found to be in proper working order with clean installation and adequate drainage lines functioning correctly.

# HVAC No Heat Service Call - Unit 10+ Years Old Responded to no heat call on aging HVAC system. Upon inspection, discovered significant rust staining on pipe insulation and surrounding surfaces, indicating prolonged moisture exposure and potential corrosion of metal components. Documented conditions with photographic evidence showing rust-colored discoloration transferred to insulation materials and adjacent ceiling areas. The extensive oxidation staining suggests active or historical water intrusion affecting system components, which may be contributing to heating system failure. Recommended further investigation of moisture source and evaluation of corroded components to restore proper heating function and prevent additional water damage to the unit.

Conducted comprehensive HVAC system assessment in basement utility area to provide replacement estimate. Evaluated existing Carrier furnace/air handler unit, associated galvanized metal ductwork system, and electrical panel configuration to determine equipment specifications and installation requirements. Documented current system layout including rectangular trunk lines, branch ducts, and insulated duct sections to plan for new equipment integration with existing infrastructure while ensuring proper sizing and compatibility for optimal system performance.

Performed warranty diagnostic service on outdoor air conditioning unit. Connected Yellow Jacket manifold gauges to measure system pressures and verify proper refrigerant charge levels across multiple refrigerant types including R-22, R-404A, and R-410A. System pressures were monitored and recorded using calibrated analog gauges reading up to 800 PSI to ensure unit was operating within manufacturer specifications and warranty compliance standards.

# Sump Pump Inspection and Service Performed comprehensive inspection and service of existing sump pump system installed in basement utility area. Verified proper operation of submersible sump pump unit within circular pit equipped with black plastic liner set into concrete floor. Tested float switch mechanism for appropriate activation and deactivation at correct water levels. Confirmed secure attachment of float assembly to pump body and verified unobstructed movement throughout full range of motion. Inspected white PVC discharge pipe for proper vertical alignment and secure mounting. Verified discharge pipe bracket and clamp assembly maintaining stable positioning. Examined two-piece sump pit cover for proper fit around discharge piping, ensuring adequate access for future maintenance while preventing debris entry into pit. Assessed overall system functionality in conjunction with visible basement mechanical equipment, including pressure tank, water treatment systems, and associa

Conducted comprehensive assessment of existing HVAC system for replacement estimate, including outdoor air conditioning condenser unit and indoor furnace system. Evaluated current 2-ton AC condenser positioned on concrete pad against exterior wall with gray electrical conduit connections and documented condition of unit housing, heat exchange coils, and protective grille assembly. Inspected basement furnace installation including ductwork configuration, metal cabinet construction, refrigerant line routing, and electrical connections. Photographed both indoor and outdoor equipment to document existing system specifications, installation methods, and spatial constraints for replacement planning. Assessed concrete pad condition, electrical service routing along vinyl siding, and clearance requirements around outdoor unit within mulched landscaping area. Reviewed basement mechanical room layout including exposed floor joists, available workspace, and existing duct transitions to determine

Completed full HVAC system replacement in residential basement utility area. Installed new furnace unit with associated vertical ductwork system including metal plenum boxes and galvanized duct sections running floor to ceiling. Configured white PVC condensate drain and venting lines for proper furnace operation. System has been tested and is fully operational.

# HVAC Install - Complete System Completed full HVAC system installation including indoor air handler unit and outdoor condensing unit. Installed new air handler in basement mechanical room with proper plenum connections and ductwork integration. Mounted outdoor condensing unit on exterior pad against building foundation with appropriate clearances. Ran and insulated refrigerant line set between indoor and outdoor units through building envelope. Installed electrical disconnect box at outdoor unit location per code requirements. Performed system startup procedures including refrigerant charging using manifold gauges to verify proper pressures and system operation. Tested all electrical connections, verified proper airflow through supply plenum, and confirmed heating and cooling functionality. System commissioned and operating within manufacturer specifications.

Responded to no cooling complaint on residential air conditioning system. Connected manifold gauge set to outdoor condenser unit and evaluated refrigerant pressures and system performance. Diagnosed cooling issue and performed necessary service procedures to restore proper system operation. System tested and confirmed operating within manufacturer specifications upon completion.

Completed comprehensive HVAC system evaluation in residential basement utility area for full equipment replacement estimate. Assessed existing furnace and air handler configuration, documented current electrical panel capacity and conduit routing, evaluated ductwork connections and plenum mounting, and photographed equipment layout to provide detailed replacement recommendations and specifications for new high-efficiency heating and cooling system installation.

# Outdoor Spigot Installation and Plumbing Rough-In Completed installation of outdoor spigot plumbing system during construction phase, routing new water supply lines through unfinished basement ceiling structure. Installed PVC and PEX piping with proper mounting brackets and clips along exposed floor joists, ensuring secure attachment and appropriate slope for drainage. Coordinated pipe routing with existing electrical conduit and HVAC systems to maintain proper clearances and building code compliance, preparing infrastructure for final connection to exterior hose bib fixture.

Completed scheduled HVAC maintenance inspection on residential system. Performed comprehensive evaluation of furnace and air handler components, including electrical connections, capacitor, and control board functionality. Inspected mounting hardware, wiring connections, and verified proper installation of all components. Documented system condition with photographs showing terminal connections and internal electrical components. All systems operating within normal parameters with no immediate service needs identified.