Reputable Home Services in West Allis

Completed full HVAC system installation including new outdoor air conditioning unit with associated coil and Honeywell Home digital thermostat. Installed exterior condensing unit on composite equipment pad with proper electrical disconnect and conduit connections, established refrigerant line sets between outdoor and indoor components, and mounted programmable thermostat on interior wall for system control and temperature management.

Responded to service call for air conditioning unit producing clunking noise during operation. Upon arrival, inspected outdoor condenser unit and surrounding components, documented equipment condition with photographs showing unit properly positioned on concrete pad with adequate clearance and access to refrigerant lines and electrical connections. Conducted operational assessment to identify source of mechanical noise and verified system functionality.

Completed full HVAC system installation including new furnace, air conditioning unit, and F100 air filtration system. Installed new air handler with vertical configuration in basement utility area, connected refrigerant line set with proper insulation, and integrated all ductwork connections. All equipment mounted, electrical connections completed, condensate drainage established, and system tested for proper operation.

Conducted estimate for air conditioning system addition to existing home with Carrier gas furnace currently installed in basement. Assessed installation requirements, reviewed existing ductwork infrastructure and determined optimal placement for outdoor condensing unit on exterior side of home near foundation with PVC condensate drainage routing. Documented existing furnace configuration, available electrical service, and recommended AC unit positioning to integrate with current heating system for complete HVAC functionality.

Completed routine cooling system maintenance visit as part of membership agreement. Performed comprehensive inspection of outdoor condensing unit, which showed significant accumulation of leaves, twigs, and organic debris in the base pan and around compressor components. Cleaned debris from unit interior, inspected compressor, capacitor, refrigerant lines, and electrical connections, and verified all components were operating within normal parameters.

Responded to commercial property for water leak originating from first floor and extending down to basement level. Upon inspection, discovered deteriorated wooden structural members with significant moisture damage and rot in the affected area, evidenced by heavy black staining on horizontal and vertical support beams. Located and repaired the source of the leak involving aged copper piping showing green patina oxidation. Addressed secondary plumbing issue involving PVC drainage system with corroded metal collar fitting causing rust staining on surrounding tiled surface. Completed installation of new water line connection for refrigerator appliance as requested.

Successfully installed a new Bradford White residential water heater in the basement utility area. The installation included proper connection of copper supply piping with brass fittings and shut-off valves, gas line hookup with appropriate controls, and venting system installation. Unit was tested for proper operation and all safety checks were completed.

Conducted on-site assessment for sump pump installation in residential property currently lacking basement water management system. Evaluated basement conditions and determined requirements for complete sump pump system including excavation for crock basin installation. Documented existing basement infrastructure including overhead ductwork showing advanced corrosion and deterioration, floor joist configuration, and foundation exterior conditions adjacent to lawn area where discharge line routing would be required.

Responded to no heat call on Lennox Elite system. Upon arrival, accessed unit and performed diagnostic inspection of internal components including blower assemblies, electrical connections, and control systems. Inspected all mechanical and electrical components, verified proper wiring connections, and checked capacitor operation. System was evaluated and appropriate corrective measures were taken to restore heating operation to the unit.

Completed installation of a comprehensive water treatment system in basement utility area, including a black water softener tank and Capital brand water filtration system with digital control head. Installed and connected white PVC piping configuration with shut-off valves, integrated copper supply lines to existing plumbing infrastructure, and established proper drainage connections using flexible corrugated hose. Mounted control components to concrete block wall, completed all electrical connections between units, verified proper system operation, and provided documentation for homeowner reference.

Completed scheduled prepaid maintenance visit on residential air handler unit located in attic space. Performed comprehensive system inspection including examination of condensate drainage lines, refrigerant connections, and electrical components. Air handler unit found in operational condition with copper refrigerant lines showing normal patina consistent with system age. Verified condensate drain system functionality and confirmed all mechanical components secured properly. System operational at time of departure.

Responded to no heat call on HVAC system less than 10 years old. Upon inspection, found loose or disconnected low-voltage wiring at the furnace control board that was preventing the heating system from receiving proper signal from the thermostat. Reconnected and secured all low-voltage wire connections at the control board terminals, verified proper wire placement according to manufacturer specifications, and tested system operation. Unit fired successfully and restored heat to the residence.

Completed full HVAC system installation in residential basement, including new Patriot high-efficiency furnace and Lennox air handler with Thermann branded components. Installed copper refrigerant line sets with proper insulation, white PVC condensate drainage and venting system, and gray metal supply/return ductwork with plenum transitions. Mounted all equipment on protective base pads over concrete flooring with proper clearances for code compliance and future maintenance access. Ran electrical connections, secured all piping and ductwork, verified system startup, and tested all components for proper operation.

Conducted comprehensive water service estimate inspection in basement utility area. Assessed aging infrastructure including corroded electrical junction box with significant rust deterioration, multiple water supply lines with brass fittings, and associated piping systems requiring evaluation for potential replacement or repair to ensure safe and reliable water service operation.

Conducted comprehensive assessment of existing HVAC system and electrical infrastructure for complete system replacement. Evaluated current electrical panel capacity and circuit configuration to ensure compatibility with new equipment specifications. Documented existing ductwork system, including main supply trunk and structural support components, to determine modification requirements for optimal airflow and equipment integration with proposed replacement unit.

# HVAC Service Report - No Heat Call Responded to no heat call on Lennox Elite furnace system. Upon arrival, conducted visual inspection of unit and opened access panel to examine internal components. Found unit in non-operational state with no active heating cycle. Performed thorough diagnostic inspection of electrical and mechanical systems within furnace compartment. Examined control board, wiring connections, capacitors, and associated components for signs of failure or malfunction. Noted significant discoloration and residue accumulation on lower metal shelf inside unit, indicating possible previous moisture intrusion or operational issues. Inspected all wire bundles and electrical connections throughout the system, including multi-colored wiring harnesses secured with zip ties. Verified integrity of connections between control systems and operational components. Checked capacitors, motor assemblies, and related electrical devices for proper function and secure mounting. Asses

# HVAC Estimate - Replacement Summary Conducted comprehensive assessment of existing hydronic heating system showing significant deterioration and corrosion throughout circulation pump assembly and associated piping infrastructure. Documentation revealed extensive mineral deposits, oxidation on copper and metal piping connections, and aging pump unit with compromised fittings requiring complete system replacement to ensure reliable heating operation and prevent potential failure. # Detailed Assessment The inspection identified a ceiling-mounted circulation pump assembly with multiple copper and metal pipe connections exhibiting advanced corrosion and mineral buildup. The pump unit displayed considerable weathering with darkened housing and deteriorated surface finish. Critical observations included white crusty deposits indicating long-term water seepage or condensation issues, oxidation on pipe joints and fittings, and visible wear on metal surfaces throughout the assembly. The pi

Installed and secured new metal HVAC ductwork in unfinished basement, including proper installation of a 90-degree elbow joint. All connections were sealed with metal tape to ensure system integrity and efficiency.

Performed inspection of furnace heat exchanger through observation port. Confirmed proper flame pattern with characteristic orange glow and no signs of flame roll-out or carbon buildup. Visual inspection indicates normal operation with no immediate concerns regarding heat exchanger integrity.

Performed scheduled HVAC maintenance service including electrical diagnostic testing with multimeter, checking system voltage readings (measured 50.89V), and verifying thermostat functionality. Confirmed Sensi thermostat was operating correctly in heating mode, maintaining 66°F ambient temperature with 40% humidity and temporary setpoint of 67°F. System is functioning within normal parameters with all connections secure.