Reliable Home Services in Franklin

Completed HVAC system installation and performed initial start-up procedures in residential basement location. Installed new ductwork with reflective insulation running parallel to existing floor joists, ensuring proper airflow distribution throughout the structure. System was energized, tested for proper operation, and all components verified to be functioning within manufacturer specifications.

Completed furnace inspection and system evaluation in residential basement mechanical area. Documented existing HVAC infrastructure including ductwork routing, supply and return air distribution systems, and equipment accessibility. Verified proper clearances around heating equipment and assessed overall mechanical room conditions. Insulated ductwork and copper plumbing lines were observed in good condition with appropriate mounting and support throughout the ceiling joists. All utility connections and structural installations were found to be properly secured and functioning as designed.

Completed scheduled HVAC maintenance on prepaid service plan. Inspected air filter and ductwork system, confirming proper airflow and system cleanliness. Filter media showed appropriate filtration capacity with clean pleated material visible through lattice frame design. Interior ductwork inspection revealed galvanized metal construction in good condition with clean surfaces and intact seams throughout the air distribution system.

# HVAC Complete System Installation Successfully completed a full HVAC system installation including both interior and exterior components. Installed new air handler unit in mechanical room on concrete pad with proper drainage provisions. Routed and secured copper refrigerant lines, electrical conduit, and condensate drainage lines throughout the installation. Mounted exterior condensing unit on building with appropriate line set penetrations through vinyl siding. Installed white PVC condensate drain lines with proper pitch and termination points at building exterior. Connected all electrical components including junction boxes and power supply conduit. Secured all refrigerant lines with proper insulation and bundling. Installed Amtrol expansion tank and associated plumbing connections. Completed all refrigerant line connections, pressure testing, and system evacuation. Energized system and verified proper operation of all components including heating and cooling cycles. All installat

Completed furnace inspection and maintenance in residential attic installation. Examined heat exchanger components showing normal patina and oxidation consistent with system age, confirmed structural integrity of ductwork connections and verified proper clearances around equipment. Assessed attic insulation placement around furnace area to ensure adequate ventilation and code-compliant spacing from heating components.

# HVAC Repair Summary Performed diagnostic inspection and component replacement on residential heating system. Accessed main unit compartment and replaced defective gas valve assembly with new OEM part, reconnecting all electrical connections including thermostat wiring and safety controls. Verified proper operation of ignition system, confirmed gas pressure settings, and tested all safety interlocks. System restored to full operational status with all components functioning within manufacturer specifications.

Completed prepaid HVAC maintenance visit and performed system diagnostics using digital multimeter. Measured electrical current at 0.26 amps and verified voltage readings, then conducted microamp testing showing -4.6 μA to assess system performance and ensure all electrical components were operating within normal parameters.

Completed prepaid HVAC maintenance visit on residential air handler system. Performed comprehensive inspection of unit, including visual examination of cabinet, electrical connections, refrigerant lines, and PVC drainage system with associated fittings and shut-off valves. All components found to be in proper working order with neat installation and no visible defects or concerns noted at time of service.

Completed HVAC system evaluation for equipment replacement estimate. Inspected existing outdoor condensing unit with deteriorated cabinet and aging components, along with indoor air handler showing signs of wear including soiled filtration media. Documented current system configuration including refrigerant line set routing, electrical connections, and drainage piping. Assessed equipment placement, pad condition, and accessibility for potential replacement unit installation. Provided comprehensive replacement recommendations based on current system age, efficiency ratings, and observed component degradation.

Completed installation of new Lennox air conditioning system with matching evaporator coil. Installed outdoor condensing unit on level pad against exterior wall with proper clearances, ran and insulated refrigerant line set through wall penetration, and mounted new evaporator coil above existing furnace in basement utility area. Connected electrical supply to outdoor unit, installed proper disconnect, and ran low voltage control wiring between indoor and outdoor components. Installed new PVC condensate drain line from coil with proper trap and termination. Pressure tested refrigerant lines for leaks, pulled vacuum on system to remove moisture and contaminants, and charged system to manufacturer specifications. Verified all electrical connections are secure and properly sized. Started system and confirmed proper operation of compressor, condenser fan, and indoor blower. Checked refrigerant pressures and temperatures to ensure system is operating within normal parameters. Verified adequa

Completed prepaid HVAC maintenance visit on Carrier Infinity furnace system. Performed comprehensive inspection of unit, verified proper operation of all components including venting system, humidifier connection, and ductwork integration, and documented equipment condition with photos for service records.

Completed prepaid HVAC maintenance visit on residential furnace system. Performed comprehensive inspection of all internal components including blower motor assembly, gas manifold connections, control board, electrical connections, and venting system. All components found to be in proper operational condition with no issues identified requiring immediate attention.

Completed scheduled prepaid maintenance visit on HVAC system. Performed comprehensive inspection of furnace components including gas valve assembly, blower motor, electrical connections, and control board. All wiring bundles, safety controls, and mechanical components were examined and found to be operating within normal parameters.

# Service Report: HVAC No Heat Call Responded to no heat call on residential furnace system over 10 years old. Upon arrival, performed complete system diagnostic including visual inspection of furnace cabinet, control board, ignition system, and gas valve operation. Checked thermostat communication and verified proper 24V control voltage at unit. Inspected heat exchanger through accessible panels and confirmed structural integrity with no visible cracks or deterioration. Tested blower motor operation and amp draw, verifying performance within manufacturer specifications. Examined flame sensor for carbon buildup and contamination that could prevent proper flame rectification. Cleaned flame sensor rod using emery cloth to remove oxidation and restore proper microamp signal. Verified proper gas pressure at manifold using manometer and confirmed inlet pressure met utility specifications. Cycled system through multiple heating cycles to verify ignition sequence, flame establishment, and

Performed indoor air quality inspection and verified proper operation of Carrier digital thermostat. System was found operating correctly in heat mode, maintaining setpoint of 72°F with all display features and controls functioning normally. No operational issues detected with the temperature control system.

Replaced corroded water supply line to toilet with new braided stainless steel flex connector. Verified proper installation and tested for leaks; system now functioning correctly with no water seepage at connection points.

Performed scheduled maintenance on HVAC system. Accessed and inspected interior components including motor assembly, control board, electrical connections, and PVC exhaust piping. All systems functioning properly with no issues identified during this preventative maintenance visit.

Responded to service call to address drainage issue. Discovered significant mineral buildup and sediment accumulation in the 1½" polyethylene pipe fittings of the residential plumbing system. Removed affected section, cleaned pipe connections, and replaced damaged components to restore proper drainage function.

Responded to callback to address drainage issue with HVAC condensate line. Reconfigured PVC piping with proper elbows to create effective drainage path away from foundation. Installed new exterior termination point with appropriate P-trap configuration to ensure proper system ventilation while preventing water intrusion.

Inspected bathroom fixture with focus on drain/stopper mechanism in white porcelain basin. Observed minor discoloration and water marks around the brushed nickel drain component. Completed assessment of stopper functionality and basin condition.