Trusted Heating, Cooling and Plumbing Services in Caledonia

Completed comprehensive tune-up on mid-efficiency gas boiler for homeowner new to the property. Performed standard maintenance procedures including inspection of all mechanical components, pressure gauge verification, electrical connections, piping systems, and expansion tank. Provided detailed orientation on thermostat operations and explained heating system controls to familiarize homeowner with equipment functionality.

Provided estimate for toilet replacement in residential bathroom. Customer has new fixture ready for installation. Assessed existing toilet condition and surrounding plumbing connections, noting deteriorated wall surface behind unit with visible moisture damage, cracking, and paint failure. Documented water supply line configuration and floor conditions for replacement procedure.

Completed comprehensive furnace tune-up on Lennox gas heating system. Performed full system inspection including burner assembly, flame sensor, heat exchanger, blower motor, and all safety controls. Verified proper combustion, cleaned components as needed, and confirmed all connections and venting are secure and functioning correctly.

Completed preventive maintenance tune-up on residential Lennox furnace system. Performed standard inspection procedures, checked all operational components, and documented equipment condition with photographic evidence showing the main furnace unit and internal components including heat exchanger and refrigerant lines.

Completed scheduled furnace tune-up and maintenance as part of prepaid membership heating visit. Replaced heavily soiled 20x25x4 air filter with new unit, as the existing filters showed significant accumulation of dust and debris that was restricting airflow. Performed comprehensive system inspection and standard maintenance procedures to ensure optimal heating system performance for the season.

Responded to no heat call on unit displaying E122 error code. Upon arrival, performed diagnostic testing with multimeter which revealed low voltage reading of 94.8V at the control board, indicating a power supply issue. Inspected electrical junction box and control wiring connections. Found loose wire connections at terminal block which were causing intermittent power delivery to the system. Secured all wire connections at terminal block, verified proper wire nut connections, and confirmed all electrical connections were tight and properly seated. Restored power to unit, cleared error code, and verified system operation with proper voltage readings. Unit now heating normally with no error codes present.

Completed water heater replacement estimate for 25-year-old conventional tank unit currently in operation. Customer declined tankless option and preferred standard tank water heater replacement. Assessed existing installation including copper supply lines, pressure relief valve, venting configuration, and electrical connections to determine replacement specifications and requirements.

Completed preventive maintenance tune-up on Goodman brand air conditioning system. Performed standard inspection of outdoor condenser unit, verified proper operation of all components, and inspected indoor air filtration system. All equipment found to be operating within normal parameters.

Completed comprehensive tune-up maintenance on two residential furnace systems, one located in the basement and one in the garage attic space. Performed standard maintenance procedures including inspection of all mechanical and electrical components, testing of capacitor functionality using digital multimeter which showed proper readings, verification of ignition system operation, and examination of heat exchanger condition. Replaced air filter media and confirmed proper venting system integrity on both units, with all systems operating within manufacturer specifications upon completion.

Completed scheduled heating maintenance visit on residential HVAC system. Performed electrical diagnostics using digital multimeter, obtaining readings to verify proper system operation and component functionality. Accessed furnace compartment to inspect internal components including blower assembly, motor, gas valve, control wiring, and associated electrical connections. All components found operating within normal parameters and system tested successfully upon completion.

Completed scheduled heating maintenance visit as part of recurring membership agreement. Performed system inspection of furnace components including blower motor assembly and heat exchanger, verified proper operation with supply air temperature reading of 198°F, and documented equipment condition through photographic records.

Completed furnace tune-up and air conditioning tune-up on split HVAC system. Inspected capacitor, blower motor, control boards, and electrical connections; verified proper operation of all components. Customer requires air filter replacement at sizes 1-3 PM Taylor specification.

Completed installation of new Carrier air conditioning condenser unit with matching evaporator coil and 15-foot refrigerant line set. The outdoor condenser was mounted on a composite pad against the building exterior with proper clearances, and copper refrigerant lines were routed along the siding to connect with the indoor evaporator coil installed above the existing furnace in the basement. All electrical connections, refrigerant lines, and condensate drainage were completed per manufacturer specifications, and the system was charged, tested, and verified operational.

Completed preventative maintenance tune-ups on two residential air conditioning systems. Performed comprehensive system diagnostics including electrical testing with digital multimeter, verified voltage readings at 244V, inspected contactors and electrical connections within disconnect boxes, and evaluated refrigerant line integrity. All components tested within normal operating parameters and systems cleared for continued operation.

Completed on-site assessment for HVAC system replacement in residential basement utility area. Evaluated existing Carrier furnace/air handler unit, associated ductwork, and available installation space. Documented current equipment configuration, clearances, and mechanical room conditions including water heater proximity, storage constraints, and existing PVC venting arrangement. Photographed equipment access points and utility connections to develop comprehensive replacement estimate.

Performed comprehensive AC tune-up on Carrier condenser unit, including system inspection and performance verification. Supply air temperature measured at 59.5°F, confirming proper cooling operation and system functionality.

Conducted estimate for replacement of existing attic-mounted air handler unit. Inspected current equipment and attic installation conditions, documenting electrical panel configuration with main disconnect and circuit breaker arrangement, as well as existing ductwork layout including black flexible ducts and silver reflective insulation materials. Provided mid-range equipment replacement options to meet customer requirements for reliable performance without premium-tier pricing.

Conducted comprehensive assessment of existing HVAC system in residential basement mechanical room. Evaluated aging furnace/air handler unit showing significant wear, surface deterioration, and outdated components with exposed internal wiring and mechanical systems. Documented current equipment configuration including ductwork layout, ventilation piping, and electrical connections to provide accurate replacement specifications and system upgrade recommendations.

Responded to no heat call on residential HVAC system less than 10 years old. Upon arrival, performed diagnostic testing using digital multimeter which revealed supply voltage reading of 240V and temperature measurement of 55.4°F at the equipment. Identified and resolved heating system malfunction, restoring proper operation and heat output to the residence.

Completed comprehensive HVAC tune-up service including inspection of electrical components, wiring connections, and capacitor within the system's control panel. All wire bundles were examined for proper routing and secure connections, and the evaporator coil was inspected for cleanliness and proper operation. System tested successfully with all components functioning within normal parameters.