Reliable Heating, Plumbing, Electrical, and Cooling Solutions for Grafton

Performed a replacement estimate evaluation of the existing 36-year-old natural gas furnace located in the basement and the 19-year-old outdoor air conditioning condenser. The condenser exhibited heavily soiled, discolored coil surfaces with rust along the cabinet base and grate, and was surrounded by overgrown vegetation and debris restricting airflow. The condensate pump in the basement showed a corroded copper line at its inlet fitting, along with visible dust and debris buildup, and both systems were documented as candidates for replacement due to age and condition.

Repaired the water main by replacing approximately 20 feet of copper supply piping, with the water supply shut off for the duration of the work. The new copper run was secured to the floor joists with strut brackets and clamps, and the system was left properly supported and ready for service.

Performed an on-site evaluation of the existing split-system air conditioning installation for a replacement estimate following a failed contactor. Inspected the indoor air handler, refrigerant line set, condensate drainage, and control components in a confined utility closet, and noted heavy staining and moisture residue around the condensate drain piping and secondary drain/safety switch area that should be addressed during replacement. Documented equipment data labels and installation conditions to determine replacement options and scope.

Installed a complete HVAC system conversion from oil to gas, including a new furnace, Lennox condenser, PVC venting and condensate drain piping, and filter cabinet. The outdoor condenser was set on a level pad and connected to the refrigerant lines, with the system charged using refrigerant. Permitted work was completed with licensed electrical connections and a disconnect installed at the unit, and the gas service is pending utility activation.

Performed a complete tune-up on the gas-fired boiler, including inspection and cleaning of the burner compartment, burners, and orifices to remove soot and heat staining. Inspected the pilot assembly, igniter/flame sensor, gas fittings, and wiring connections for proper condition and secure fastening, and verified safe, normal operation of the unit upon completion.

Performed a seasonal furnace tune-up, accessing the burner compartment and control cabinet to inspect the burner assembly, control board, transformer, relays, and low-voltage thermostat terminal connections (W, C, Y, G, HUM) for secure termination and proper wire routing. Verified wiring harness integrity and cleaned accumulated dust and debris from the cabinet interior, then reinstalled the access panel and confirmed the unit was ready for operation.

Completed installation of Alpha-1 sump pump replacement system in basement utility area. Installed new sump pump unit with yellow float switch assembly in existing concrete basin, connected discharge piping using white PVC with proper joints and fittings, and configured electrical controls and power connections to ensure proper pump operation and automatic water level management.

Completed mid-efficiency boiler tune-up and seasonal maintenance inspection. During the inspection, documented severely corroded suspension springs showing extensive rust and oxidation damage that will require monitoring or replacement to prevent system failure. Unit is currently operational following standard tune-up procedures.

Completed scheduled heating system maintenance and tune-up as part of recurring membership agreement. Performed comprehensive furnace inspection, verified thermostat operation showing proper 72-degree setpoint and schedule programming, and conducted electrical diagnostics measuring 0.5 amp current draw to confirm safe system operation.

Completed estimate for replacement of existing gas furnace located in basement mechanical room. Assessed current HVAC system including gray metal furnace unit with return air grille and associated ductwork, as well as existing Honeywell digital thermostat. Provided replacement options and recommendations for new equipment installation.

Provided estimate for rerouting water heater venting system from existing chimney configuration to exterior wall termination. Assessed current AO Smith water heater installation and evaluated venting requirements for compliance with manufacturer specifications and local codes. Recommended exterior wall venting solution to improve draft efficiency and eliminate chimney dependency.

Responded to a supply line gate valve leak in the utility area. Inspected the plumbing assembly featuring copper piping and gate valves mounted on the wall, identified the source of the leak, and completed necessary repairs to restore proper function and eliminate water seepage. System was tested and confirmed operational upon completion.

Conducted on-site assessment of existing oil-fired furnace system in basement mechanical room to provide estimate for conversion to gas-fired heating system. Evaluated current ductwork configuration, including existing metal supply and return plenums, and documented equipment layout and available space for new gas furnace installation. Confirmed gas line is already run to the location, simplifying the conversion process. Photographed existing HVAC equipment, ductwork connections, and mechanical room layout to prepare accurate replacement estimate and verify compatibility with new gas furnace specifications.

Responded to emergency service call for furnace system evaluation. Upon inspection, found existing Goodman furnace unit in basement mechanical room required red-tagging due to safety concerns. Completed comprehensive assessment of HVAC system including ductwork, ventilation components, and auxiliary equipment. Provided detailed replacement estimate for new furnace installation. Coordinated installation scheduling to accommodate customer's extended absence, arranging access through local family members for completion during two-month travel period with confirmed two to four-hour arrival window and advance notification protocol.

Completed full tune-up maintenance on HVAC system including inspection of control board, wiring harness connections, and reversing valve assembly. Verified all electrical connections secure, checked refrigerant circuit components for proper operation, and documented system condition with interior cabinet photography showing copper reversing valve solenoids and control board in good working order.

Completed inspection and estimate for outdoor spigot replacement. Assessed existing copper plumbing infrastructure in crawl space, including vertical supply line connections, pipe insulation condition, and access points to exterior hose bib. Documented current installation configuration with black insulated joints and provided recommendations for replacement work.

# Sump Pump Inspection Performed comprehensive pre-winter sump pump inspection on an 8-year-old system. Documented existing conditions of submersible pump assembly, discharge piping, and basin components. Inspection revealed significant corrosion and rust deterioration on copper discharge pipes, with surface oxidation evident throughout the piping system. Verified pump housing integrity, float switch operation, and proper water level in concrete basin. Photographed all components including deteriorated pipe surfaces, pump assembly with circular cover plate and mounting bolts, flexible discharge hose, and basin conditions to document current system status prior to winter season.

Responded to service call regarding attic ventilation fans creating excessive negative pressure in the home, resulting in dangerous downdraft conditions on the water heater flue. Assessed ventilation system and combustion appliance venting to identify pressure imbalance issues that could lead to backdrafting of combustion gases into the living space.

Completed estimate for sump pump replacement with battery backup system installation. Assessed existing sump pump unit showing signs of wear and operational degradation, documented current setup including pump housing, discharge piping configuration, and sump basin condition. Evaluated workspace accessibility and determined requirements for upgraded system with integrated battery backup to ensure continuous operation during power outages. Photographed existing equipment and basin opening to document pre-replacement conditions and provide specifications for replacement unit sizing and installation planning.

Responded to callback for disconnecting drain hose on recent installation. Upon inspection, found condensate drain line was insufficient length causing repeated disconnection at fitting. Replaced drain hose with properly sized tubing, secured all connections, and verified proper drainage flow with no leaks.