HVAC, IAQ, & Plumbing Services in Hartford, WI

# HVAC No Heat Service Call Responded to no heat complaint on residential HVAC system. Upon arrival, performed diagnostic inspection of furnace unit. Removed access panel to examine internal components and electrical systems. Visual inspection revealed significant corrosion and rust deterioration on metal framework and base platform, indicating prolonged moisture exposure. Multiple wire harnesses and circuit boards were examined for proper connections and functionality. Documented equipment condition through photographs showing corroded metal surfaces contrasting with operational electrical components. Blower motor assembly and control boards were inspected. System evaluated for safety concerns related to deteriorated metal components and potential impact on electrical systems. Equipment shows signs of extended service life despite being under ten years old, with environmental factors contributing to accelerated deterioration of metal components.

Completed scheduled prepaid heating maintenance visit on residential furnace system. Performed comprehensive inspection of air handler unit, including blower motor assembly, internal mechanical components, and ventilation system. Verified proper operation of condensate drain lines and PVC vent piping connections. Inspected refrigerant lines and insulation integrity. All systems found operating within normal parameters and unit left in proper working condition.

Installed a 50-gallon Bradford White electric water heater (Model BBUS4A737IRE41) at the service location. Unit was picked up from Ferguson supply house, delivered to site, and successfully installed per manufacturer specifications with warranty documentation completed.

# HVAC Service Report Responded to no heat call on residential furnace system. Upon arrival, removed access panels and performed comprehensive diagnostic evaluation of unit. Conducted electrical testing using multimeter to verify power supply and circuit integrity throughout the system. Inspected internal wiring, control board, and all electrical connections for proper operation and safety. Identified issue preventing heat operation and completed necessary repairs to restore full heating functionality. Verified proper operation of all safety controls and confirmed unit cycling correctly. Reinstalled access panels and left system in proper working order.

Performed diagnostic service on Whirlpool water softener experiencing complete drainage failure. Inspected unit installation, control panel functionality, and associated plumbing connections including copper supply and drain lines. Documented equipment condition and utility room configuration with water heater proximity for service records.

Completed comprehensive furnace tune-up including full system diagnostics with multimeter testing of electrical components and circuit board functionality. Verified proper operation of all mechanical components, inspected air filter condition, and confirmed system is operating safely and efficiently within manufacturer specifications.

Completed comprehensive furnace tune-up on residential HVAC system located in basement mechanical room. Performed standard maintenance inspection including examination of blower motor assembly, refrigerant lines, electrical connections, and ventilation components; verified proper operation of all system functions and ensured unit specifications met manufacturer requirements.

Provided estimate for replacement of leaking Rheem Professional model PROE502-RH9150 50-gallon electric water heater located in basement utility area. Prepared detailed materials list including new 50-gallon electric water heater, expansion tank with adapter, CPVC and copper press fittings, and necessary piping materials for complete installation.

Responded to emergency service call for HVAC system evaluation. Conducted comprehensive assessment of existing furnace, humidifier, and air conditioning equipment in basement mechanical room. Provided detailed replacement estimate for heating and cooling system components based on equipment age, condition, and homeowner requirements.

Conducted on-site plumbing estimate for bathroom tub/shower fixture replacement and kitchen faucet installation. Assessed existing chrome tub spout and shower control valve showing significant rust staining and mineral deposit buildup at wall penetrations, indicating potential water intrusion and need for fixture replacement. Reviewed new kitchen faucet assembly with pull-down spray hose, supply lines, and counterweight system for installation estimate.

Responded to service call for non-functioning thermostat. Upon arrival, found Badger brand programmable thermostat displaying 59°F with system set to cooling mode in manual operation. Inspected unit, verified display functionality, and assessed thermostat programming and wiring connections to restore proper operation.

Completed standard HVAC tune-up service on system. Technician brought replacement filter for unit and performed routine maintenance procedures. Customer was provided with promotional service offer information during visit.

Conducted on-site assessment of existing fuel oil furnace system in basement of 1900 sq ft, 2-story single-family residence to provide replacement estimate. Current furnace unit approximately 18 years old, installed circa 2006, located in basement mechanical area. Inspected existing equipment configuration including air handler, ductwork connections, and associated HVAC components. Documented system layout with photographic evidence showing control module, wiring harness, galvanized ductwork with foil insulation, and mounted humidifier unit. Noted moisture condensation present on foam insulation surfaces within equipment compartment. Evaluated existing infrastructure including plumbing lines, gas connections, electrical service, and available space for replacement equipment installation. Provided comprehensive replacement estimate for new fuel oil furnace system suitable for heating requirements of 1900 sq ft residential structure.

Responded to service call for kitchen faucet malfunction and dishwasher water supply issues. Upon arrival, performed diagnostic assessment of the kitchen plumbing system. Identified that the existing kitchen faucet was failing and causing inadequate water flow, which was subsequently affecting the dishwasher's ability to fill properly during its cycle. The dishwasher was shutting down mid-cycle due to insufficient water pressure and volume reaching the appliance. Recommended replacement of the kitchen faucet to restore proper water delivery to both the sink and connected dishwasher supply line. Documented existing conditions with photographs of the kitchen sink area and exterior hose bib for service records.

Conducted estimate for replacement of 16-year-old Kenmore model 153.339762 water heater with 48-gallon capacity that is actively leaking. Customer requested upgrade to 60-gallon unit to accommodate increased hot water demand. Assessed existing installation including copper supply lines, exhaust venting, pressure relief valve configuration, and floor drainage. Documented current unit condition with photographs showing leak evidence and utility room layout. Provided recommendations for new water heater installation including proper venting requirements, code-compliant pressure relief valve discharge piping, and expansion tank evaluation.

Replaced gooseneck single-handle kitchen faucet with chrome finish fixtures, including side sprayer attachment and soap dispenser. Installed new supply lines and P-trap assemblies for double-basin sink configuration. Customer also reported water softener and iron filter system cycling nightly between 9:59-11:00 PM, which appears to be operating on its programmed regeneration schedule.

Completed comprehensive furnace tune-up on residential gas heating unit, including full system inspection, cleaning of burner assembly and flame sensor, filter replacement with customer-supplied filters, and verification of proper venting through PVC exhaust pipes. Tested blower motor operation, checked all electrical connections, and confirmed system is operating safely within manufacturer specifications. Unit passed all safety checks and is ready for the heating season.

Completed full tune-up maintenance on residential HVAC system in basement utility area. Performed comprehensive system diagnostics using Testo 310 combustion analyzer to verify proper operation, efficiency, and safety parameters. Customer provided replacement filter for installation during service visit.

Completed preventive maintenance tune-up on residential gas furnace system. Performed comprehensive inspection of unit, ductwork, and connections; verified proper operation of all components; and documented system condition with photos for service records.

Completed scheduled heating system maintenance visit as part of recurring membership agreement. Performed comprehensive inspection of furnace components including blower motor assembly, gas valve operation, electrical connections, and control board functionality. Utilized digital diagnostic equipment to verify system performance parameters and operational readings. All components found operating within normal specifications with proper wire connections and no visible deterioration noted.