Reliable Home Services in Pewaukee

Completed installation of new residential central air conditioning system including outdoor condensing unit and evaporator coil. Mounted gray condensing unit on concrete pad with proper clearances from building structure, installed gray electrical disconnect box on exterior wall per code requirements, and ran refrigerant line set with black foam insulation from outdoor unit through wall penetration to indoor coil location. Connected copper refrigerant lines, electrical wiring, and condensate drain line to complete system integration. Performed vacuum and pressure testing of refrigerant circuit using diagnostic equipment to verify system integrity prior to charging. Successfully commissioned system with all components operating within manufacturer specifications.

Completed installation of Lennox EL18KCV-048-230B04 outdoor condensing unit with matching evaporator coil system. Unit was positioned on gravel pad against exterior wall with proper clearances maintained, electrical connections completed per manufacturer specifications at 208/230V single-phase service, refrigerant lines installed and system charged with 10 lbs 1 oz of R-454B refrigerant per factory specifications. Condensate drain line installed with PVC piping, all electrical requirements met including 50-amp maximum overcurrent protection and minimum circuit ampacity of 28.7 amps. System startup performed, operational parameters verified, and unit tested for proper cooling operation.

Successfully installed a complete HVAC system including indoor air handler/furnace unit in the basement utility area with proper ductwork connections and required labeling. Installed complementary dehumidifier system with appropriate wiring and completed exterior condensing unit installation with PVC drain line configuration according to manufacturer specifications.

Conducted comprehensive assessment of existing HVAC system for replacement estimate. Exterior inspection revealed wall-mounted PVC ventilation pipes and outdoor condensing unit showing signs of age and exposure to harsh weather conditions. Interior evaluation of the Carrier WeatherMaker 9200 furnace system identified potential upgrade opportunities for improved efficiency. Recommended full system replacement to ensure optimal performance and energy efficiency for the residence.

Conducted site assessment in basement area for HVAC replacement, documenting existing ductwork configuration and available installation space. Measured floor area using folding ruler to determine appropriate unit sizing requirements for the new system.

Responded to no heat call for aging furnace (10+ years). Upon inspection, accessed internal components by removing access panel, revealing blower motor assembly, electrical connections, and control board. Performed diagnostic testing, cleaned accumulated dust from critical components, and verified proper operation of gas line and safety systems before returning unit to service.

Conducted inspection of HVAC system in unfinished basement mechanical room. Observed central furnace unit with connected metal ductwork extending to ceiling distribution points. Verified proper installation of ventilation components and electrical connections within the ongoing construction environment.

Performed scheduled prepaid maintenance visit on HVAC system. Inspected electrical connections and wiring, noting proper installation of control wiring with appropriate color coding and terminal connections. System is functioning within normal parameters after service.

Successfully installed complete residential HVAC system in basement utility room, including furnace unit with proper ductwork connections and PVC ventilation piping. System was properly mounted and secured on concrete floor with all manufacturer specifications followed for optimal performance and efficiency.

Performed scheduled maintenance on HVAC system under existing service agreement. Inspected interior electrical components and control valve assembly, verifying proper wire connections and operational status. All components were found to be in good working condition with no issues detected.

Conducted inspection of existing HVAC system in partially finished basement area. Documented current ductwork configuration including PVC ventilation pipes and galvanized metal ducting components. Evaluated ceiling space for new system installation constraints, noting transition between exposed utility ceiling and finished living areas with recessed lighting. Prepared estimate for complete system replacement based on observed structural conditions and space limitations.

Performed scheduled preventative maintenance on HVAC system. Inspected and replaced dirty air filter to improve system efficiency. Conducted visual examination of internal components including gas valve assembly, wiring connections, and blower motors, all of which were found to be in proper working condition.

Completed installation of new furnace unit with proper mounting and electrical connections. Inspected interior components for proper assembly and verified all manufacturer labels and specifications. Connected control unit to power supply and completed final system check to ensure proper operation.

Conducted assessment of aging Trane XL 80 furnace system showing signs of moisture accumulation on top surface. Evaluated existing galvanized ductwork configuration including main trunk line, round connections and elbow joints. Prepared comprehensive replacement estimate for customer consideration.

Successfully installed a complete Lennox HVAC system in the customer's residence, including proper connection to the existing Generac transfer switch. System installation included furnace unit with PVC venting and all necessary electrical and plumbing connections. Final inspection confirmed proper operation of all components in winter conditions.

Conducted comprehensive assessment of existing HVAC system in residential basement mechanical room, including evaluation of furnace/air handler unit, associated ductwork, and PVC ventilation components. Inspection also included examination of electrical circuit breaker panel to verify proper power supply and capacity for potential replacement equipment.

Conducted inspection of under-sink cabinet plumbing infrastructure, examining shut-off valves and supply lines. Identified potential installation points for new fixture. Documentation captured existing toilet paper storage configuration and current valve placement to ensure proper planning for upcoming fixture installation.

Conducted inspection of existing HVAC system installation, focusing on air handler mounting and plumbing connections. Documented current configuration including wall clearance and electrical junction box setup. Prepared estimate for complete system replacement with attention to proper fitting of equipment against interior wall and reconnection of existing plumbing with appropriate valves and conduit routing.

Performed routine HVAC tune-up service with temperature diagnostics showing supply air temperature of 146°F, confirming proper heating operation. System inspection revealed normal operating conditions with no issues detected.

Performed routine HVAC tune-up service, inspecting system components and connections. Noted minor dust accumulation in the air duct connection with early signs of rust formation along metal seams. Examined cooling coils which showed slight discoloration and minor corrosion but remain in functional condition.